- Home /
- Nox Composites
Shop By
Currently Shopping by
- Category: Remove This Item Project 321 Bike Wheels
Filter
- Category
-
- PWB Signature Series (4)
- Wheel Packages By Brand (139)
- Wheel Packages By Wheel Type (139)
- Wheel Accessories (72)
- Rims (361)
- Hubs (206)
- Spokes (73)
- Nipples (47)
- Astral Rolf Bike Wheels (6)
- Bitex Bike Wheels (5)
- Boyd Cycling Bike Wheels (4)
- Chris King Bike Wheels (4)
- Derby Composite Bike Wheels (4)
- DT Swiss Bike Wheels (6)
- ENVE Composites Bike Wheels (4)
- H Plus Son Bike Wheels (3)
- HED Bike Wheels (4)
- Hope Tech Bike Wheels (7)
- IBIS Bike Wheels (3)
- Industry Nine Bike Wheels (5)
- KinLin Bike Wheels (6)
- Mavic Bike Wheels (2)
- NOX Composite Bike Wheels (7)
- Onyx Racing Bike Wheels (7)
- Pacenti Bike Wheels (3)
- Paul Components Bike Wheels (2)
- Phil Wood Bike Wheels (1)
- PWB Composite Bike Wheels (7)
- Race Face Bike Wheels (4)
- Shimano Custom Bike Wheels (5)
- Son Dynamo Bike Wheels (7)
- Spank Bike Wheels (3)
- Stans No Tubes Bike Wheels (4)
- Velo Orange Bike Wheels (2)
- Velocity Custom Hand Built Wheel Packages (6)
- Whisky Bike Wheels (4)
- White Industries Bike Wheels (6)
- WTB Bike Wheels (4)
- Zipp Bike Wheels (4)
Nox Composites
There are no products matching the selection.
I'm still new at wheel building But I learn very quickly and I needed more information on how to properly take Hub measurements to type into the Spoke calculater! So I went to UBI and read how to correctly take measurements and I typed it into their calculater and the difference between theirs and Prowheelbuilers is that Prowheelbuilders was more accurate than UBI's calculater. I did Not know if I should add or subtract to the closest mm: of measurement? So I compared the two different options and Prowheelbuilders Calculater made it easier for me to decide on what length I should go with! if I would have used the length that UBI calculated it would have been a little bit to Short on my Drive side! I figured what the Hell I'll go with prowheelbuilders calculation and it paided off for me! The Spoke Lengths Where Right on the Money!!!. I'm Well Pleased with my New DT Swiss Spokes and they look great as well! I'm using rims with offset spoke holes and I subtracted 1mm from the None drive side and added 1mm To the Drive side like I should and Prowheelbuiders was more accurate! I laced a Novatec D882SB Rear Hub up to a Loaded AmX Gold Anodized Free ride rim with ERD: of 532 and it is running very Smoothly!Joseph T Riker December 15, 2013
I'm a heavy rider and a clyde of sorts at 280lbs. I knew I could depend on the stock wheels for a limited lifespan. So far I've had FOUR sets (3 road, one MTB) of custom wheels built from both the signature and custom programs. Not one has required a spoke wrench yet with seasons of abuse that I've put them through. All are still in service. I put 50-100 miles a week on my bikes, and the wheels have been 100% reliable. A good set of wheels can vastly improve the quality of your biking experience. This is the real deal with a lot of experience and no BS. Trust in this builder - they know their products. Bitex hubs are an awesome value.Jeremy Watts October 28, 2020