- Home /
- Nox Composites
Currently Shopping by
- Axle Size
- Thru Axle Rear 12x135mm (3)
- Thru Axle Rear 12x142mm (4)
- QR Front 9x100mm (3)
- QR Rear 10x135mm (3)
- Thru Axle Front 9x100mm (1)
- Thru Axle Rear 10x135mm (3)
- Thru Axle Front 12x100mm (4)
- Thru Axle Front 15x100mm (3)
- Thru Axle Front 15x110mm Boost (1)
- Thru Axle Front 20x110mm Boost (1)
- Bolt On Rear 10x135mm (3)
- Lefty 60mm 2.0 Super Max (1)
- Lefty 73mm Olaf (1)
Nox Composites - Brass - Aluminum Rims
There are no products matching the selection.
I'm still new at wheel building But I learn very quickly and I needed more information on how to properly take Hub measurements to type into the Spoke calculater! So I went to UBI and read how to correctly take measurements and I typed it into their calculater and the difference between theirs and Prowheelbuilers is that Prowheelbuilders was more accurate than UBI's calculater. I did Not know if I should add or subtract to the closest mm: of measurement? So I compared the two different options and Prowheelbuilders Calculater made it easier for me to decide on what length I should go with! if I would have used the length that UBI calculated it would have been a little bit to Short on my Drive side! I figured what the Hell I'll go with prowheelbuilders calculation and it paided off for me! The Spoke Lengths Where Right on the Money!!!. I'm Well Pleased with my New DT Swiss Spokes and they look great as well! I'm using rims with offset spoke holes and I subtracted 1mm from the None drive side and added 1mm To the Drive side like I should and Prowheelbuiders was more accurate! I laced a Novatec D882SB Rear Hub up to a Loaded AmX Gold Anodized Free ride rim with ERD: of 532 and it is running very Smoothly!Joseph T Riker December 15, 2013
As a senior rider who has done his own wrenching for the past 50 plus years, I’ve successfully tackled most bike building, maintenance, and repair issues with which one is confronted. However, until recently, I avoided building wheels as I thought the process was too daunting. But, I finally placed wheel building as an item on my bucket list.Craig Tate July 30, 2015
When I started researching wheel building components and techniques, I was astonished by the extent of conflicting, or erroneous information provided by print and online sources, including manufacturers’ websites — it was as if wheel building was a cult speciality and practitioners were forbidden to provide clear, correct procedures to an outsider. It also became clear how little most bike shop employees knew about wheel building.
Enter ProWheelBuilder. I was fortunate to find I lived reasonably close to the store and I made an appointment to meet with Richard, the owner. Upon our meeting, I entered the discussion believing I had a pretty good idea of the wheels I wanted to build and was primarily looking for components and encouragement. But, it quickly became clear that even the selection of components was more involved than I initially thought. Fortunately, Richard has an encyclopedic knowledge of the combinations and permutations of components and benefits thereof — I won’t go into details here, but suffice it to say you’ll be better off telling Richard what you want to do with the wheels rather than asking for specific components. Richard will offer several viable options at varying price points. You will be very happy with the result whether you decide to build the wheels, or have Richard build them.
To the last point, I can tell you I built several wheelsets for the enjoyment and sense of accomplishment. But, frankly, because of the expense of the required tools, it is far less expensive to have Richard build the wheels for you. Further, despite being fairly adept with tools, it took me about 4-hours to do what Richard can do in 20-30 minutes. Richard has years of experience and has invented, patented, and manufactured a number of wheel building jigs and tools for the industry and utilizes these tools and expensive measuring devices to facilitate his quick and extremely accurate build process.
I will also tell you that once you build, or buy a hand-built set of wheels, you will no longer be satisfied with the typical machine built wheels that are delivered on most new bicycles, or sold in big box stores as replacement, or upgrade wheels. You can really tell the difference.
I have been very happy with Richard’s advice and assistance with my builds. I highly recommend ProWheelBuilder’s products and services to anyone wanting a quality wheelset.